Remove the Handle Mounting Nut A nut holds the toilet handle in place. good luck. Unscrew the new mounting nut from the handle by turning it clockwise. Re: Removing old plastic nuts; Author: plumbhelp (MA) u can use whats called a basin wrench. On most toilets, this nut is left-handed or reverse-threaded, which is opposite from a typical nut. FREE Shipping on orders over $25 shipped by Amazon. I am trying to replace the valves inside the toilet tank. Remove the mounting nut. Using either a wrench or a screwdriver (depending on whether your toilet has bolts or screws), unscrew the bolts or screws from either side of the bottom of the toilet. 98. $8.98 $ 8. Loosen the nut from inside of the tank using an adjustable wrench if necessary. ). I wasn't able to loosen it at all. If you were to face the nut … Your new toilet handle will come with the lever, mounting nut, and rubber O-ring already attached to it. 3) Remove the Old Handle. It goes from the handle to the flapper. Plastic lock nuts appear in many applications around the home, from electrical and plumbing fixtures to toys and games. It should be located at the place where the handle comes in from outside of the tank. I can't drill through the top of the bold because the hinge is still attached and also won't come off. The nut is completely stripped and the metal bolt it is attached to is rusted. I have done this before and always seem to have a problem. In most cases, your toilet will be connected to the floor by at least 2 bolts or screws. The handle is generally held in place by a nut that is secured against the wall of the tank. This means you will turn the nut clockwise to loosen. Jmkcoz Angle Fitting Side Mount Toilet Flush Lever Handle for TOTO Kohler Toilet Tank Universal Fit For Most Toilet, Toilet Repair Handle with Nut, Copper Lever. This nut can be loosened with your adjustable wrench. Look inside the tank and find the chain clip that’s attached to the lever. This is a small chain hooked onto the inside portion of your toilet handle. Use a crescent wrench to remove the nut inside the tank that holds the handle in place. Okay, I thought replacing the flush handle would be a 5 minute job, but when I pulled off the tank lid I found that the nut and bolt threads on the inside of the tank were encrusted with what I'm assuming is limescale (see pic). Our toilet has been getting progressively hard to flush, to the extent that the toilet handle has now cracked. Once the nut has been removed, the handle … 4.5 out of 5 stars 604. Pull off the mounting nut and O-ring from the new handle. This means, to tighten the nut, you must screw counterclockwise, and to loosen, clockwise. Therefore I was going to try and remove the syphon element to replace the flapper plasticy bit at the bottom (apologies for the technical terms here! Using the right tools and process, safely remove plastic lock nuts… With wrench or pliers, unscrew the handle nut (turning clockwise) and pull out the handle and lift arm (image b). Get it as soon as Mon, Jan 11. they are normally used to tighten and remove those nuts when they are brass. I've tried filing the plastic away, using a hacksaw on both the nut and the bolt below and above the toilet, to no avail. Undo the clasp to detach the handle from the rest of your toilet. but i've used the wrench on the tough plastic nuts also. To remove the old handle, shut off the water to toilet and flush twice. Disconnect the wire or chain from the lift arm (image a). when u mount the new faucet, put some pipe dope, or never seize on the threads, then draw up the new nuts. But, because they are softer than metal, remove them without breaking them in half. Unscrew the bolts or screws from the bottom of the toilet. Be careful: For the vast majority of toilets, the nut has left-handed threads, which means they turn in the reverse direction of a normal nut. This time I cannot remove the two plastic nuts under the tank, holding the metal intake tube to the tank and the valve. Slide the nut down the lever until it's completely removed and then remove the O-ring.